▾

JB systems AVM-1 digital amplifier module 300W RMS

Discontinued, this product can no longer be ordered.

No alternatives found

JB systems AVM-1 digital amplifier module 300W RMS
Product no: W-01712 Bax Music Warranty: This product comes with a 3-year warranty.

General

The Vibe series by JB Systems isn't active in itself, but with the AVM-1 amp module you can make it active! Easily convert your Vibe 10 MKII and Vibe 12 MKII. Just take off the rear panel of your satellite speakers and plug in the AVM-1. Subsequently mount the AVM-1 in the cabinet - job done!

Power and options of the AVM-1

The power of the AVM-1 is brought by the digital class D circuit. This means that the module can remain small and light of weight. It's still able to produce 300 watts RMS at 8 ohms!

With the lockable speaker connector, you can also connect a passive speaker of 8 ohms. Then the module will deliver a total of 500 watts RMS, and you will be able to drive Vibe 10 cabinets on one AVM-1!

A 100Hz filter ensures that your satellite speakers don't put out low frequencies. This is especially handy if you are working with an active sub! The module filters out all lows before they're amplified, which is very efficient!

Tips or comments about this product

Please note: the 4-ohm power is only applicable when a second 8-ohm speaker is connected. The power is then divided over the two speakers!
Please note: picture 2 is an application example.

Specifications

Weight and dimensions including packaging

Weight (incl. packaging)	4,0 kg
Dimensions (incl. packaging)	76,0 x 5,0 x 5,0 cm

Product specifications

powerful amp module
easy mounting in a few minutes
fit for the Vibe 10 and 12 (MKII)
class D digital circuitry
power: 8 ohms 300 W RMS
power: 4 ohms 500 W RMS
balanced/unbalanced XLR in and output
100Hz low-cut filter
lockable output for an extra passive speaker (8 ohms)
IEC power connector
on/off switch
frequency range (+/-2dB): 20 to 20,000 Hz
signal/noise ratio (A-weighted) > 86 dB
damping factor > 320
cooling: cooling fins and fan with magnetic field
signal connectors: 3-pole XLR
amplifier output: locking connector +1/-1
protections: thermic, limiter, short-circuiting, DC voltage
fuse: 5x 20 mm T5AL, 250 V
mains voltage: 230V AC, 50 Hz
maximum power consumption: 630 W @ 4 ohms
dimensions: 275 x 145 x 72 mm
mounting hole: 253 x 123 mm
weight: 2 kg

A review can no longer be written about this item

Reviews from other countries

Translate all reviews into English View original reviews

clemens W. October 9, 2016

Wrote the following about JB systems AVM-1 digital amplifier module 300W RMS

Ik heb de versterker gemonteerd in een zelfbouw pa project van mij.
(visaton ontwerp) 2 stuks van 8 ohm
De versterker is mooi ligt, en kleiner dan ik zou verwachten.
Het geluid is gewoon goed en ook hard genoeg. hij ging niet clippen en bleef mooi onvervormd.
Ik wil nog een keer het opgenomen vermogen meten . Dit zegt dan ook iets van het afgegeven vermogen lijkt me.
Ook werd de versterker zeker niet warm.
Enigste puntje de ventilator gaat iets meer lawaai maken als de box iets resoneert.
Dit hoeft niets te betekenen,dit en omdat ik niet weet hoe hij zich houd na een geruime tijd.
vandaar 4 en geen 5 sterren.