The Shure UA440 antenna rack mount kit allows you to move the antennas of your Shure wireless receiver to the front of your 19" rack for easy access and enhanced reception.
The Shure UA221 is a passive antenna splitter/combiner kit. Use it to split an incoming signal into two outgoing signals, or to combine two incoming signals into a single signal.
The Shure PS43E is here to replace the PS31E, PS40E and PS41E mains power adapters, and is compatible with receivers from the LX, UC, SC, ULX, SLX and PSM Series.
Need a new belt clip for your Shure RPM400 preamp? Just grab this official replacement clip.
The Shure UA806-RSMA is an SMA coaxial cable with reverse polarity. It is possible to use this 180 cm cable to mount antennas at longer distances on GLX-D wireless systems.
The Shure RK187T1-B clip has been designed to fit all Shure WL18XM Series lavalier microphones, comes in black and ties down a single clip-on mic.
If the grille on your Shure SM86 or SM87A is dirty, worn, damaged or lost, replace it with the Shure RK214G. This is therefore a grille that replaces the standard grille.
Shure PS51E 5.5V DC power adapter for Shure chargers. This power adapter is equipped with a European safety plug and a plug adapter for Shure charging modules.
The Shure AMVL-CLIP can be used to replace the tie clip that comes with the Shure MVL lavalier microphone as standard - just in case it gets lost or you're in need of a spare.
The Shure SB904 lithium-ion battery pack delivers up to 12 hours of run-time on a full charge.
Energy-efficient 15V DC in-line power supply for Shure equipment.
The Shure RK187T2-B Clip has been designed to fit all Shure WL18XM Series clip-on lavalier microphone, comes in black and has space for two microphones.
The universal Shure A25E microphone clip is fully compatible with any microphone with a 25 to 30mm shaft diameter, making it the ideal for models like the Shure KSM9, KSM9HS and KSM8.
This single-slot charging station can be used to recharge a Shure SB904 rechargeable battery.
The Shure SBC80-903-E battery charger has enough slots to recharge eight Shure SB903 rechargeable batteries at a time, making it an indispensable accessory for extensive Shure SLX-D-based setups.
Windscreen for the Shure SM81 microphone. Reduces breathing and wind noise.
Premium 1/4" right angle instrument cable with lockable TA4F connector.
Did you break the grille of your Shure SM58 microphone? No need to panic, you can simply replace it with the RK143G microphone grille!
The Shure SB900C is a rechargeable Li-ion battery that can be used with several Shure products.
The Shure UA860SWB is a 1/2 wave antenna that improves the reception of the Shure SLX, ULX, LIC, UHF and UHF-R, allowing for a better reception.
To protect your SM7B, SM7A or SM7's recordings from pops and taps caused by the wind or your breath, Shure developed the A7WS windshield to suppress that unwanted noise without affecting the quality of the overall sound.
Just in case they get worn out or go missing, the Shure RK379 microphone clip and windshield pack is compatible with the Shure SM31FH Fitness microphone headset.
The Shure WA310 cable will make your wireless bodypack transmitter even more versatile, allowing you to connect it to any dynamic microphone with an XLR connector.
Rechargeable lithium-ion battery for the Shure ADX1M transmitter.
Shure microphones need to be properly protected against unwanted noise, and the Shure A85WS windshield does just that. It's suited for Shure Beta 87A/C, SM87A, SM86, SM85 and BG5.1 microphones.
The Shure UA8100 is a coaxial cable with two BNC plugs, which can, for instance, be used for connecting additional antennas or as an extension cable for antennas.
Make sure you don't accidentally pull the microphone plug out of your bodypack transmitter with the Shure WA340 threaded TA4F adapter!
Do you want to hook up your dynamic microphone to a bodypack transmitter? With this kit, you can equip your microphone cable with a connector that allows you to do just that, basically converting your mic into a wireless one!
The Shure RPM40SO is a kit consisting of 10 Standoffs for RPM40(S)TC Dual and Single tie pin clips. This kit is suitable for all TL40 lavalier microphones.
Do you want to place your UHF antenna just a bit further than its cable allows you to? Use this UHF extension cable. Cable length: 3.3 metres.
You can use the RPW184 microphone head if you want to give your Shure wireless handheld transmitter the properties and sound of the Shure KSM9 microphone. It's a great replacement part, and you can even keep it as a backup.
The Shure SBC200 Dual Docking is a recharging station for two SB900 batteries, body packs or transmitters. It is compatible with P9RA, P10R, ULXD1 and ULXD2 handheld/body pack transmitters. Used in combination with the SBC200-E.
Fully protect the Shure MOTIV MV88 iOS microphone from wind noise on location with the tailor-made Shure AMV88-FUR Windjammer. This efficient recording tool was developed in collaboration with Rycote.
The Shure RPM400LEMO is a wired microphone preamplifier with an adapter from TQG to XLR connector. This preamplifier is suitable for all Shure TwinPlex microphones such as the TL45, 46, 47, 48 and TH53 headsets.
When your Shure Beta57A or 56A microphone's grille is damaged, the mic is much more vulnerable. Be sure to replace it in time with the RK320 microphone grille!
The Shure SBC10-903-PS charger accommodates a separately available SB903 battery for Shure's SLX-D series transmitters.
Wind and breath noise don't belong in a clear recording or amplification that is made with a Shure MX/WL180 series microphone! Which is why Shure offer these microphone windscreens!
This is the perfect universal microphone mount to fit mics to percussion instruments like drums, for instance. The big jaw exerts perfect grip, yet you're still able to move the microphone.
Breath and wind noise, mechanical noise, handling noise; these are all issues that are common for microphone users. Luckily there is an answer to all of these problems: the Shure A15HP in-line high-pass filter!
You can use the Shure A15AS attenuator to protect your mixer, PC or amplifier from input overload. It reduces your microphones output level by 15, 20 or 25 dB to prevent it from overloading any inputs or channels.
The Shure RPW112 is a microphone head meant for Shure wireless transmitters. All RPW heads are interchangeable, so you can switch to different microphone types on the fly!
These 5 colour-coded ID caps allow you to quickly distinguish between various BLX2 handheld transmitters. Suited for the PG, SM and Beta wireless systems.
UA600 front mount antenna kit for Shure SLX4, ULX4, UR4S and UR4D receivers.
The Shure UA505 remote antenna mounting bracket kit allows you to place your Shure 1/2 wave antenna's wherever you want for improved reception and easier access!
The Shure KSM11 is a condenser capsule for your Shure wireless system like you haven't heard before. Even under the most challenging conditions, your voice remains clear and in the foreground.
Add it to any existing Shure wireless system, and the Shure Nexadyne RPW204 capsule will give your live rig an enormous upgrade. Expect unbelievable clarity that reaches every corner of the venue thanks to Revonic Dual Engine tech.
Add it to any existing Shure wireless system, and the Shure Nexadyne RPW200 capsule will give your live rig an enormous upgrade. Expect unbelievable clarity that reaches every corner of the venue thanks to Revonic Dual Engine tech.
